Select-comfort U 3000 Bedienungsanleitung

Another satisfied Sleep Number® bed ownerSELECT COMFORT CORPORATION6105 TRENTON LANE NORTHMINNEAPOLIS MN 55442BUSINESS REPLY MAILFIRST-CLASS MAIL PERM

4INSERT SUPPORT BEAMSTabs up, match “A” end with “A” groove; match “B” end with “B” groove.Joints fit tightly, push firmly until top is flush. Slide the

5PLACE DECK PANELSSlide panels in until they are flush on sides.Panels fit snugly, do not force.Queen shownReminderKing foundation consists of two Tw

Foundation FrequentlyAsked QuestionsMake sure the letter on the center support beam matches the side rail. For example, the end of the center beam lab

MattressAssembly10 11

MattressAssembly12 13BEFORE YOU BEGINu Carefully check the contents of your mattress boxes u OrientationThese instructions refer to “left” and “ri

CONTENTSCarefully check the contents of your mattress boxes and compare with the list below. Each component is clearly labeled with the part name an

12UNZIP MATTRESS COVERSet cover aside.14POSITION MATTRESS COVERPlace on foundation or on existing bed platform. Make sure the holes in the bottom of

3415PLACE CORNER LOCKSPlace one in each corner.Corner locks must go under the border wrap.INSTALL FOAM BORDER WALLS Place long border walls alon

165INSTALL FOAM BORDER WALLSPlace short border walls at the head and foot.Make sure the foam border walls are connected securely and squarely. The

717CONNECT FIRMNESS CONTROL™ SYSTEMPlace the Firmness Control™ System on the floor at the head of the bed and plug in the power cord.Key Step: Pass

37Please tell us why you like your new Sleep Number Bed by Select ComfortTM.Comments: Name Email Address Bed model purchasedCity/State/Zip Your Sle

189VERIFY BORDER WRAP POSITIONINGPosition the border wrap over foam border walls and air chambers as shown.Important Notice: To ensure compliance wi

YOU’RE DONE! NEXT STEP u THE FIRMNESS CONTROL™ SYSTEM10MATTRESS COVERZip the top of the mattress cover.Store air chamber caps inside mattress at hea

The caps are in the Firmness Control™ System box. Please store these in the mattress cover in case you should ever want to disassemble your bed and

Will my bed deflate if there is a power surge or power loss?No, your mattress will maintain its firmness. To protect your Firmness Control™ System, we d

22For the best looking, most crisp appearance, customers should fully inflate the mattress (100 if using a digital Sleep Number® remote). If going to

FirmnessControl™ System23

24FirmnessControl™ SystemTHINGS TO REMEMBERu Reasons to alter the firmness of your bed- strained muscles - back pain - weight change - pregnancy - su

25WHAT IS A SLEEP NUMBER® SETTING?Your Sleep Number® is a setting between 0–100 that represents the ideal combination of mattress comfort, firmness an

26IDENTIFY YOUR REMOTE AND ITS FUNCTIONSBUTTONFUNCTIONwakes when any button is pressedwakes when L or R button is pressedwakes when any button is p

27u Step 1- Lie on one side of the Sleep Number® bed in your normal sleep position, holding your remote.u Step 2- Evaluate your comfort level.u Step

Welcome and CongratulationsWelcome and Congratulations,Congratulations on your purchase of The Sleep Number Bed by Select Comfort™! You’re about to j

No, your mattress will maintain its firmness. To protect your Firmness Control™ System, we recommend using a surge protector.Will my bed deflate if the

29SleepJournalCommentsSleep Number® setting Number of nights

30CommentsSleep Number® setting Number of nights

31MattressCare2560

32MATTRESS CAREThe cover of your SLEEP NUMBER® mattress may be spot cleaned with carbonated water. Do not dry clean the mattress cover or put it in a

31Accessories33

34PERSONALIZED COMFORT FROM HEAD TO TOESM WITH EXCLUSIVE SELECT COMFORT® ACCESSORIESPillows Our sleep-position pillows are available in memory foam,

Warranty and Comfort Club®3580

36DEFECTIVE OR DAMAGED COMPONENTS If any component of the mattress or foundation is found to be defective in materials or workmanship within first two

37Please tell us why you like your new Sleep Number Bed by Select ComfortTM.Comments: Name Email Address Bed model purchasedCity/State/Zip Your Sle

WHAT’S INSIDEu Foundation Assembly ...pg 3 u Mattress Assembly ...pg 11u

37Please tell us why you like your new Sleep Number Bed by Select ComfortTM.Comments: Name Email Address Bed model purchasedCity/State/Zip Your Sle

Another satisfied Sleep Number® bed ownerSELECT COMFORT CORPORATION6105 TRENTON LANE NORTHMINNEAPOLIS MN 55442BUSINESS REPLY MAILFIRST-CLASS MAIL PERM

Another satisfied Sleep Number® bed ownerSELECT COMFORT CORPORATION6105 TRENTON LANE NORTHMINNEAPOLIS MN 55442BUSINESS REPLY MAILFIRST-CLASS MAIL PERM

FoundationAssembly3Note: Texture and surface appearance may vary.

FoundationAssembly4 5BEFORE YOU BEGINu Carefully check the contents of your foundation boxes u Decide where to put your new bedu Make sure there

2 each 2 each 2 each 4 each 6 6 6 12 2 4 4 4 2 2 2 4 1 1 1 1 0 0 4 0 Twin Full Queen KingCONTENTSCarefully check the cont

1CONNECT SIDE RAILSPush the components labeled A side rail and B side rail together. Joints fit tightly. Push firmly.2INSERT PINSlide pins in, “T” end

3Pin Pin 7INSERT SUPPORT/ END BEAMSFor Twin, Queen and Eastern King models:– insert support beams with tabs up and textured side out.For Full and Cal